diff --git a/devices/pc8080/machine/vt100/machine.xml b/devices/pc8080/machine/vt100/machine.xml
index 6e5b876b6..ecf8153c1 100644
--- a/devices/pc8080/machine/vt100/machine.xml
+++ b/devices/pc8080/machine/vt100/machine.xml
@@ -28,4 +28,7 @@
SET-UP
+
+ TEST RECEIVER
+
diff --git a/disks/dec/rk03/xxdp/README.md b/disks/dec/rk03/xxdp/README.md
index 341dae26e..d597a37c8 100644
--- a/disks/dec/rk03/xxdp/README.md
+++ b/disks/dec/rk03/xxdp/README.md
@@ -50,7 +50,7 @@ Refer to [Help](/disks/dec/rl02k/xxdp/#help) from the RL02K version.
The "D" (DIRECTORY) command displays the following information:
ENTRY# FILNAM.EXT DATE LENGTH START
-
+
1 HDDKB0.SYS 2-JAN-70 2 000112
2 HMDKB1.SYS 2-JAN-70 17 000113
3 HDDKB1.SYS 2-JAN-70 2 000114
diff --git a/disks/dec/rl02k/xxdp/README.md b/disks/dec/rl02k/xxdp/README.md
index 4a2e437f8..efe419b28 100644
--- a/disks/dec/rl02k/xxdp/README.md
+++ b/disks/dec/rl02k/xxdp/README.md
@@ -18,7 +18,7 @@ available for drive "RL0", click **Load**, and wait for the message:
Then start the machine (click **Run**) and make sure the following prompt has been displayed:
PDP-11 MONITOR V1.0
-
+
BOOT>
At the prompt, type "BOOT RL0". The following text should appear:
@@ -26,12 +26,12 @@ At the prompt, type "BOOT RL0". The following text should appear:
CHMDLD0 XXDP+ DL MONITOR
BOOTED VIA UNIT 0
28K UNIBUS SYSTEM
-
+
ENTER DATE (DD-MMM-YY):
-
+
RESTART ADDR: 152010
THIS IS XXDP+. TYPE "H" OR "H/L" FOR HELP.
-
+
.
NOTE: Any RL11 disk drive (RL0-RL3) can be used. RL0 was selected for demonstration purposes.
@@ -50,7 +50,7 @@ The "H" (HELP) command displays the following information:
Monitor Commands
----------------
-
+
R run a program
L load a program
S start a program
@@ -59,8 +59,8 @@ The "H" (HELP) command displays the following information:
F set the terminal fill count
E enable alternate system device
H type help information
-
-
+
+
DRS Commands
------------
Execution
@@ -70,27 +70,27 @@ The "H" (HELP) command displays the following information:
CONTINUE continue diagnostic at test that was
interrupted by a ^C
PROCEED continue from an error halt
-
+
Units Under Test
----------------
ADD activate a unit for testing
DROP deactivate a unit
DISPLAY print a list of device information
-
+
Flags
-----
FLAGS print status of all flags
ZFLAGS reset all flags
-
+
Statistics
----------
PRINT print statistical information
-
+
Exitting
--------
EXIT return to XXDP+ runtime monitor
-
-
+
+
DRS Command Switches
--------------------
/TESTS:test-list execute only the tests specified
@@ -99,11 +99,11 @@ The "H" (HELP) command displays the following information:
/EOP:ddddd report end-of-pass after each ddddd passes
(ddddd = 1 to 64000)
/UNITS:unit-list command will affect only specified units
-
-
+
+
DRS Flags
---------
-
+
Flag Effect
---- ------
HOE halt on error - control is returned to runtime
@@ -127,8 +127,8 @@ The "H" (HELP) command displays the following information:
LOT loop on test
EVL execute evaluation (on diagnostics which have
evaluation support)
-
-
+
+
UPD1 Commands
-------------
CLR clear UPD1 program buffer
@@ -140,8 +140,8 @@ The "H" (HELP) command displays the following information:
DUMP dump a program image
DEL delete a file
BOOT bootstrap a device
-
-
+
+
UPD2 Commands
-------------
File Manipulation
@@ -151,7 +151,7 @@ The "H" (HELP) command displays the following information:
FILE transfer a file or files
DEL delete a file or files
REN rename a file
-
+
File Modification
-----------------
CLR clear UPD2 program buffer
@@ -161,14 +161,14 @@ The "H" (HELP) command displays the following information:
HICORE set upper memory limit for dump
LOCORE set lower memory limit for dump
DUMP dump a program image
-
+
New Medium Creation
-------------------
ZERO initialize a medium
SAVM save a monitor on a disk
SAVE save a monitor on a tape
COPY copy entire medium
-
+
Miscellaneous
-------------
ASG assign a logical name to a device
@@ -176,18 +176,18 @@ The "H" (HELP) command displays the following information:
READ read a file to check validity
EOT write end-of-tape mark
DRIVER load a device driver
-
+
Returning to Monitor
--------------------
BOOT bootstrap a device
EXIT return control to the runtime monitor
-
+
Printing
--------
PRINT print a file on the line printer
TYPE type a file on the console terminal
-
-
+
+
PATCH Commands
--------------
BOOT Boot specified device
@@ -200,8 +200,8 @@ The "H" (HELP) command displays the following information:
PATCH Crreate patched file
SAVP Save input table
TYPE Print input table on terminal
-
-
+
+
XTECO Non-edit Commands
-----------------------
TEXT - create new text file
@@ -211,23 +211,23 @@ The "H" (HELP) command displays the following information:
PRINT - print a file on the line printer
DIR - list directory of specified medium
EXIT - return to monitor
-
-
+
+
XTECO Edit Commands
-------------------
-
+
Pointer Location
----------------
L - move the pointer line by line
C - move the pointer character by character
J - move the pointer to the beginning of text
ZJ - move the pointer to the end of text
-
+
Search
------
S - search for specified string in text now in memory
N - search for specified string in remainder of text file
-
+
Modify/Display Text
-------------------
T - type text
@@ -235,7 +235,7 @@ The "H" (HELP) command displays the following information:
K - delete line(s)
I - insert text
A - append text to that currently in memory
-
+
Terminating Edit Mode
---------------------
EX - exit edit mode
@@ -246,7 +246,7 @@ The "H" (HELP) command displays the following information:
The "D" (DIRECTORY) command displays the following information:
ENTRY# FILNAM.EXT DATE LENGTH START
-
+
1 MMDP .SAV 3-MAR-83C 17 000310
2 MTDP .SAV 3-MAR-83C 17 000331
3 HSAAD0.SYS 3-MAR-83 24 000352
diff --git a/disks/dec/rl02k/xxdp/ekbad0/README.md b/disks/dec/rl02k/xxdp/ekbad0/README.md
index 04d365dc3..92ab89938 100644
--- a/disks/dec/rl02k/xxdp/ekbad0/README.md
+++ b/disks/dec/rl02k/xxdp/ekbad0/README.md
@@ -12,22 +12,22 @@ From the
p. 1-6:
11/70 CPU DIAGNOSTIC PART 1
-
+
ABSTRACT:
-
- This diagnostic is the first part of the 11/70 CPU, it designed to detect and
- report logic faults in the CPU. Any fault detected in this program causes the
- program to "HALT". After this, run the second part of the CPU test, EKBBF0.
-
+
+ This diagnostic is the first part of the 11/70 CPU, it designed to detect and
+ report logic faults in the CPU. Any fault detected in this program causes the
+ program to "HALT". After this, run the second part of the CPU test, EKBBF0.
+
OPERATING PROCEDURES:
Set the switch register by (RD console)
CON = xxxxxxWZ
(W = deposit xxxxxx into console switch register)
- (R = read and type console switch settings)
- (Z = switch console terminal back to program)
-
+ (R = read and type console switch settings)
+ (Z = switch console terminal back to program)
+
.R EKBAD0
-
+
SWITCH SETTINGS
SW15 = 1 halt on error
SW14 = 1 loop on test
@@ -51,4 +51,3 @@ on [bitsavers.org](http://bitsavers.trailing-edge.com/pdf/dec/pdp11/microfiche/f
PRODUCT NAME: CEKBAD0 11/70 CPU #1
DATE CREATED: MAY, 1980
MAINTAINER: DIAGNOSTIC ENGINEERING
-
diff --git a/disks/dec/rl02k/xxdp/ekbbf0/README.md b/disks/dec/rl02k/xxdp/ekbbf0/README.md
index 802ffd407..fe0f7fdd7 100644
--- a/disks/dec/rl02k/xxdp/ekbbf0/README.md
+++ b/disks/dec/rl02k/xxdp/ekbbf0/README.md
@@ -12,21 +12,21 @@ From the
p. 1-7:
11/70 CPU DIAGNOSTIC PART 2
-
+
ABSTRACT:
-
- This diagnostic is the second part of the 11/70 CPU, it tests advanced
- instructions and miscellaneous logic.
-
+
+ This diagnostic is the second part of the 11/70 CPU, it tests advanced
+ instructions and miscellaneous logic.
+
OPERATING PROCEDURES:
Set the switch register by (RD console)
CON = xxxxxxWZ
(W = deposit xxxxxx into console switch register)
- (R = read and type console switch settings)
- (Z = switch console terminal back to program)
-
+ (R = read and type console switch settings)
+ (Z = switch console terminal back to program)
+
.R EKBBF0
-
+
SWITCH SETTINGS
SW15 = 1 halt on error
SW14 = 1 loop on test
@@ -144,28 +144,28 @@ The source code listing for TEST 40 matches the code above, and begins at the sa
ERROR 235 ;RED ZONE REFERENCE FAILED TO TRAP
BR 8$
3$: MOV #STACK,SP ;RESET THE SP
- MOV #CPUSPUR,@#ERRVEC ;RESTORE LOCATION 4
+ MOV #CPUSPUR,@#ERRVEC ;RESTORE LOCATION 4
ERROR 237 ;BEN 13 FAILED TO PUP.00
BR 8$
1$: CMP @#0,#6$ ;DID BEN 13 FAIL?
- BEQ 7$ ;BRANCH IF NO
- MOV #STACK,SP ;RESET THE SP
- MOV #CPUSPUR,@#ERRVEC ;RESTORE ERRVEC
- ERROR 240 ;BEN 13 FAILED TO BRK.80
- BR 8$
+ BEQ 7$ ;BRANCH IF NO
+ MOV #STACK,SP ;RESET THE SP
+ MOV #CPUSPUR,@#ERRVEC ;RESTORE ERRVEC
+ ERROR 240 ;BEN 13 FAILED TO BRK.80
+ BR 8$
7$: CMP #-1,@#336 ;;DID YEL ZONE OCCUR?
- BNE 8$ ;BRANCH IF NO
- CLR @#336 ;SETUP FOR LOOPING
- ERROR 251 ;YEL ZONE IN RED REGION
+ BNE 8$ ;BRANCH IF NO
+ CLR @#336 ;SETUP FOR LOOPING
+ ERROR 251 ;YEL ZONE IN RED REGION
;
;TEST TO ENSURE PSW REFERENCE VIA THE SP CAUSES A RED ZONE TRAP
8$: MOV #63$,$LPERR ;SETUP ERROR LOOP
63$: MOV #4$,@#ERRVEC ;SETUP ERRVEC
- MOV #PSW,SP ;PUT ADDRESS OF PSW IN SP
- CLR (SP) ;EXECUTE THE TRAP CAUSING INSTRUCTION
- MOV #1076,SP ;RESET THE SP
- MOV #CPUSPUR,@#ERRVEC ;RESTORE ERRVEC
- ERROR 241 ;NO RED ZONE ON STACK OVERFLOW
+ MOV #PSW,SP ;PUT ADDRESS OF PSW IN SP
+ CLR (SP) ;EXECUTE THE TRAP CAUSING INSTRUCTION
+ MOV #1076,SP ;RESET THE SP
+ MOV #CPUSPUR,@#ERRVEC ;RESTORE ERRVEC
+ ERROR 241 ;NO RED ZONE ON STACK OVERFLOW
PDPjs was failing to trigger a RED stack violation on this instruction:
@@ -189,20 +189,20 @@ and begins at the same address (031532):
;* OCCURS AND NOT THE T BIT TRAP.
;;***************************************************************
TST63: SCOPE
- MOV #TST64,NEXTTST ;SAVE ADDRESS OF NEXT TEST
- MOV #^D1990,$ICNT ;ADJUST ITTERATION COUNT
- MOV #10$,$LPADR ;SETUP LOOP ADR
+ MOV #TST64,NEXTTST ;SAVE ADDRESS OF NEXT TEST
+ MOV #^D1990,$ICNT ;ADJUST ITTERATION COUNT
+ MOV #10$,$LPADR ;SETUP LOOP ADR
10$: MOV #2$,@#TPVEC ;SETUP TELEPRINTER VECTOR
- MOV #1$,$LPERR ;SETUP ERROR LOOP
+ MOV #1$,$LPERR ;SETUP ERROR LOOP
1$: MOV #STACK,SP ;INITIALIZE THE SP
- SPL 3
- MOV #BIT6,@$TPS ;SET PRINTER INTERRUPT FLAG
- MOV #15,@$TPB ;SEND CHARACTER
- WAIT ;EXECUTE INSTRUCTION UNDER TEST
+ SPL 3
+ MOV #BIT6,@$TPS ;SET PRINTER INTERRUPT FLAG
+ MOV #15,@$TPB ;SEND CHARACTER
+ WAIT ;EXECUTE INSTRUCTION UNDER TEST
;FAILURE
- CLR @$TPS ;CLEAR INTERR ENABLE BIT
- ERROR 377 ;WAIT INSTRUCTION DID NOT
- BR 5$ ;WAIT FOR INTERRUPT
+ CLR @$TPS ;CLEAR INTERR ENABLE BIT
+ ERROR 377 ;WAIT INSTRUCTION DID NOT
+ BR 5$ ;WAIT FOR INTERRUPT
After setting and hitting a breakpoint at 031532, we can step through the instructions in this test:
diff --git a/disks/dec/rl02k/xxdp/ekbee1/README.md b/disks/dec/rl02k/xxdp/ekbee1/README.md
index d31c1aeab..cf7828714 100644
--- a/disks/dec/rl02k/xxdp/ekbee1/README.md
+++ b/disks/dec/rl02k/xxdp/ekbee1/README.md
@@ -12,36 +12,36 @@ From the
p. 1-10:
11/70 MEMORY MANAGEMENT TEST
-
+
ABSTRACT:
-
- This program was designed using a "BOTTOM UP" approach starting with the smallest segment of MEMORY
- MANAGEMENT logic and building up to cover all the logic. The program begins by testing some of the
- internal CPU data and address path and address detection logic, then works outward through the MEM.
- MANAGEMENT registers. It is assumed that both the CPU and the CACHE have been tested, or are known
- to be good.
-
+
+ This program was designed using a "BOTTOM UP" approach starting with the smallest segment of MEMORY
+ MANAGEMENT logic and building up to cover all the logic. The program begins by testing some of the
+ internal CPU data and address path and address detection logic, then works outward through the MEM.
+ MANAGEMENT registers. It is assumed that both the CPU and the CACHE have been tested, or are known
+ to be good.
+
OPERATING PROCEDURES:
- Set the switch register by
- CON = xxxxxxWZ
- (W = deposit xxxxxx into console switch register)
- (R = read and type console switch settings / CON = R)
- (Z = switch console terminal back to program)
-
+ Set the switch register by
+ CON = xxxxxxWZ
+ (W = deposit xxxxxx into console switch register)
+ (R = read and type console switch settings / CON = R)
+ (Z = switch console terminal back to program)
+
.R EKBEE1
-
+
SWITCH SETTINGS
- SW15 = 1 halt on error
- SW14 = 1 loop on current test
- SW13 = 1 inhibit all error typeouts
- SW12 = 1 inhibit trace trapping
- SW11 = 1 inhibit iterations
- SW10 = 1 ring bell on error
- SW09 = 1 loop on error
- SW08 = 1 loop on test in SWR <06:00>
- SW07 = 1 inhibit multiple error typeouts
- SW06 = 1 selects subtest
- ...
+ SW15 = 1 halt on error
+ SW14 = 1 loop on current test
+ SW13 = 1 inhibit all error typeouts
+ SW12 = 1 inhibit trace trapping
+ SW11 = 1 inhibit iterations
+ SW10 = 1 ring bell on error
+ SW09 = 1 loop on error
+ SW08 = 1 loop on test in SWR <06:00>
+ SW07 = 1 inhibit multiple error typeouts
+ SW06 = 1 selects subtest
+ ...
The closest we have to a source code listing of the EKBEE1 diagnostic comes from some
[scanned microfiche](http://archive.pcjs.org/pubs/dec/pdp11/diags/AC-7975E-MC_CEKBEE0_1170_MEM_MGMT_May80.pdf)
@@ -59,13 +59,13 @@ the PDF (p. 199 of the source code listing):
;*TEST 122 KT BEND
;*
;* THIS TEST ENSURES THAT TMCE KT BEND GOES LOW ON AN ODD
- ;* ADDRESS ERROR, SL RED, AND NEXM. THIS IS DONE BY EXECUTING
- ;* AN INSTRUCTION FOR EACH Of THESE THESE CASES THAT ALSO
- ;* CAUSES A KT ABORT. THE ABORT SHOULD NOT BE HONORED.
- ;*
- ;* NOTE: ON A KB11-E OR KB11-EM THE KT ABORT SHOULD BE HONORED OVER A
- ;* NEXM TRAP. IF THIS IS A KB11-E/EM THEN THIS FEATURE IS TESTED.
- ;;***************************************************************
+ ;* ADDRESS ERROR, SL RED, AND NEXM. THIS IS DONE BY EXECUTING
+ ;* AN INSTRUCTION FOR EACH Of THESE THESE CASES THAT ALSO
+ ;* CAUSES A KT ABORT. THE ABORT SHOULD NOT BE HONORED.
+ ;*
+ ;* NOTE: ON A KB11-E OR KB11-EM THE KT ABORT SHOULD BE HONORED OVER A
+ ;* NEXM TRAP. IF THIS IS A KB11-E/EM THEN THIS FEATURE IS TESTED.
+ ;;***************************************************************
As noted in the *mapVirtualToPhysical()* function in [cpustate.js](/modules/pdp11/lib/cpustate.js), this test
begins at PC 076060, which is exactly 0100 bytes lower than the address shown in the source code listing (076160).
diff --git a/docs/pcx86/examples/components.css b/docs/pcx86/examples/components.css
index 4d6519bb0..82802b7af 100644
--- a/docs/pcx86/examples/components.css
+++ b/docs/pcx86/examples/components.css
@@ -161,6 +161,7 @@
background-color: #000000;
}
.pcjs-rled {
+ float: left;
width: 8px;
height: 8px;
margin: 4px;
diff --git a/modules/pc8080/lib/serialport.js b/modules/pc8080/lib/serialport.js
index 05c407174..1c8bd1d5e 100644
--- a/modules/pc8080/lib/serialport.js
+++ b/modules/pc8080/lib/serialport.js
@@ -358,7 +358,7 @@ SerialPort8080.prototype.setBinding = function(sHTMLType, sBinding, control, sVa
*
* Note that I've judiciously avoided using terms "escape notation" or "escape sequence" to talk about
* these sequences, because ESC is one of the additional characters I want to support, and using the word
- * "escape" in both contexts is WAY confusing.
+ * "escape" in both contexts is WAY too confusing.
*/
sValue = sValue.replace(/\\e/g, String.fromCharCode(0x1b));
diff --git a/modules/shared/templates/components.css b/modules/shared/templates/components.css
index 0f23a2f16..12357fb1a 100644
--- a/modules/shared/templates/components.css
+++ b/modules/shared/templates/components.css
@@ -166,6 +166,7 @@
background-color: #000000;
}
.pcjs-rled {
+ float: left;
width: 8px;
height: 8px;
margin: 4px;
diff --git a/versions/pc8080/1.30.4/components.css b/versions/pc8080/1.30.4/components.css
index 4d6519bb0..82802b7af 100644
--- a/versions/pc8080/1.30.4/components.css
+++ b/versions/pc8080/1.30.4/components.css
@@ -161,6 +161,7 @@
background-color: #000000;
}
.pcjs-rled {
+ float: left;
width: 8px;
height: 8px;
margin: 4px;
diff --git a/versions/pcx86/1.30.4/components.css b/versions/pcx86/1.30.4/components.css
index 4d6519bb0..82802b7af 100644
--- a/versions/pcx86/1.30.4/components.css
+++ b/versions/pcx86/1.30.4/components.css
@@ -161,6 +161,7 @@
background-color: #000000;
}
.pcjs-rled {
+ float: left;
width: 8px;
height: 8px;
margin: 4px;
diff --git a/versions/pdpjs/1.30.4/components.css b/versions/pdpjs/1.30.4/components.css
index 4d6519bb0..82802b7af 100644
--- a/versions/pdpjs/1.30.4/components.css
+++ b/versions/pdpjs/1.30.4/components.css
@@ -161,6 +161,7 @@
background-color: #000000;
}
.pcjs-rled {
+ float: left;
width: 8px;
height: 8px;
margin: 4px;